- Atlas
- Engineering
- Power Electronics
Power Electronics
Power electronics is the branch of electrical engineering that converts and controls electric power by switching it on and off very fast.
10 frameworks, from 1920 to today · Electrical Engineering · Engineering
- Phase-fired controller 1920-Present
- Power Semiconductor Device Physics and Design 1955-Present
- Electric Machine Drives and Motion Control 1960-Present
- Pulse-Width Modulation 1970-Present
- Switched-mode power supply 1970-Present
- Field-Oriented Control 1971-Present
- Averaged Small-Signal Modeling 1975-Present
- Resonant and Soft Switching 1980-Present
- Grid-Connected Converter Control 1990-Present
- Wide-Bandgap Power Devices 2010-Present
Overview
Power electronics is the branch of electrical engineering that converts and controls electric power by switching it on and off very fast. Instead of burning off excess energy as heat in a resistor, a power electronic circuit repeatedly interrupts the current and lets inductors, capacitors, and transformers reshape the resulting pulses into the voltage and current a load needs. The field's central problem is efficiency: how to change one form of electrical energy into another—AC to DC, DC to AC, one voltage to another, one frequency to another—while losing as little as possible1. Its central tools are the switch, the magnetic component, and the control loop. Because so much of modern life runs on electricity that must be converted, power electronics sits underneath everything from phone chargers and laptop adapters to electric vehicles, data centers, and the transmission lines that carry renewable power across continents.
Mercury Arc to Thyratron: Rectification Before Semiconductors
The first practical power conversion was rectification—turning alternating current into direct current12. In the early twentieth century, industrial DC loads and, later, radio and battery charging needed steady DC, and the mercury-arc rectifier supplied it. The device passed current through an arc in mercury vapor, conducting in one direction only. It was bulky, fragile, and needed careful starting, but it could handle large currents, and by the 1920s it powered tramways, railways, and electrochemical plants. The glass-bulb and later steel-tank mercury rectifiers were the workhorses of industrial DC supply for decades.
The thyratron, a gas-filled tube with a control grid, added a crucial capability: the moment of ignition could be controlled3. That made phase control possible—delaying the start of conduction within each AC cycle to vary the average output voltage4. Phase-controlled rectification became the standard way to regulate large DC supplies, and it remained in use long after solid-state devices arrived. The same principle—varying the firing angle to set the output—is still the basis of the thyristor phase-controlled rectifiers used in high-power industrial drives and in high-voltage direct current transmission.
The Semiconductor Switch Arrives
The invention of the transistor at Bell Labs in 1947 changed electronics, but early transistors could not handle power. The decisive device for power electronics was the thyristor, announced by General Electric in 1957. A thyristor is a four-layer semiconductor switch that, once triggered by a small gate pulse, latches on and conducts until the current through it falls below a holding level. It could block thousands of volts and carry hundreds of amperes, and it was far more efficient and compact than any gas tube. Within a decade, thyristors were replacing mercury rectifiers in industrial rectification and making new applications possible.
The thyristor's limitation is that it can only be turned on by its gate, not off; it turns off only when the current naturally reverses or drops. This shaped circuit design for years. Engineers built line-commutated converters, in which the AC supply itself provided the voltage that turned the thyristor off, and forced-commutated circuits with auxiliary components to switch it off on demand. The thyristor made high-voltage direct current (HVDC) transmission practical: the first modern solid-state HVDC link, the Gotland connection in Sweden, went into service in 1954 using mercury valves, and thyristor-based HVDC followed in the 1970s, allowing power to be transmitted over long distances with lower losses than AC.
The Transistor That Could Be Turned Off
The next turning point was the power transistor that could be switched off by its control terminal. The power bipolar junction transistor (BJT) arrived in the 1960s and 1970s, and the power MOSFET—a metal-oxide-semiconductor field-effect transistor—became practical for power in the late 1970s and 1980s. Unlike the thyristor, these devices could be turned off at will, which opened the door to switched-mode operation: switching at high frequency, many thousands of times per second, so that small magnetic components could handle large power.
The insulated-gate bipolar transistor (IGBT), developed in the 1980s, combined the MOSFET's easy voltage control with the BJT's low conduction loss15. It became the dominant device for medium- and high-power applications—motor drives, traction, and later electric vehicles. The parallel development of device physics and design—doping profiles, breakdown voltage, safe operating area, thermal management—became a discipline in its own right, because a power device must survive voltages and currents that would destroy a signal transistor.
Switched-Mode Conversion and Pulse-Width Modulation
The idea that reshaped the field was switched-mode power conversion. In a switching converter, a transistor chops the input into pulses, and an inductor and capacitor smooth the pulses into a regulated output. Because the switch is either fully on (low voltage across it) or fully off (no current through it), it dissipates little power, and efficiency can exceed 90 percent—far above the linear regulators that burned the difference between input and output as heat16.
The key control method is pulse-width modulation (PWM): the switch is turned on and off at a fixed frequency, and the fraction of each cycle it spends on—the duty ratio—sets the output78. Varying the duty ratio regulates the voltage8. PWM made switching converters predictable and easy to control, and it became the standard technique across the field. The buck converter (steps voltage down), the boost converter (steps it up), and the buck-boost and isolated variants (flyback, forward, push-pull, bridge) became the basic building blocks taught to every student. The 1970s and 1980s saw these topologies move from laboratory curiosity to commodity: switching power supplies replaced linear supplies in computers, televisions, and industrial equipment.
Modeling and Control
As converters spread, engineers needed to predict and stabilize their behavior. A switching converter is a nonlinear, time-varying system, which is hard to analyze directly. The breakthrough was averaged small-signal modeling: average the converter's behavior over one switching cycle to get an equivalent continuous model, then linearize it around an operating point. This yields transfer functions that control theory can handle, so a designer can choose a feedback compensator that keeps the output steady despite load changes and input variations. The approach, developed through the 1970s and consolidated in textbooks, turned converter design from trial and error into a systematic discipline. State-space averaging extended the method to more complex converters and to systems with multiple energy-storage elements.
Feedback control also brought motion control into the field's orbit. Electric machine drives—controlling the speed and torque of motors—depend on power converters feeding the motor, and on control loops that regulate current, speed, and position. The development of field-oriented control for induction motors in the early 1970s, which made an induction motor behave like a separately excited DC motor by controlling its flux and torque components independently, was a landmark. It required fast power switching and fast computation, and it tied power electronics tightly to motor drives. Variable-frequency drives for industrial motors, and later for electric vehicles, became one of the largest applications of the field.
Resonant and Soft Switching
Hard-switched converters turn the transistor on and off while voltage and current are both present, and each transition dissipates energy as heat. As switching frequencies rose to shrink components, these losses and the electromagnetic interference they caused became limiting. Resonant and soft-switching techniques address this by shaping the voltage and current waveforms so that the switch turns on or off when one of them is near zero. A resonant converter uses an inductor and capacitor tuned to ring, and the switch is timed to the ringing; a soft-switched circuit uses auxiliary components to force a zero-voltage or zero-current transition9. These methods reduce losses and allow higher frequencies, at the cost of more complex design and greater sensitivity to load conditions. They found their place in applications where high frequency and low noise matter, such as some server power supplies and induction heating.
Wide-Bandgap Devices
Silicon dominated power semiconductors for decades, but silicon has limits: its breakdown field and thermal conductivity cap how high a device can switch and how much heat it can shed. Wide-bandgap materials—gallium nitride (GaN) and silicon carbide (SiC)—have larger bandgaps, higher breakdown fields, and better thermal performance. SiC devices, commercialized from the 2000s and 2010s, can block high voltages and switch faster than silicon at high temperatures, making them attractive for electric vehicles, solar inverters, and traction. GaN devices target high-frequency, lower-voltage applications such as fast chargers and data-center power. These materials are not replacements for silicon everywhere—cost and reliability still favor silicon in many roles—but they are pushing efficiency and power density upward, and they are reshaping converter design because faster switching demands new attention to layout, parasitics, and electromagnetic compatibility.
Grid-Connected Converters and HVDC
At the scale of power systems, power electronics has become central. HVDC transmission using thyristor and, later, voltage-source converters allows power to flow over long distances and between asynchronous grids. Voltage-source converters, built from IGBTs with PWM control, can also provide reactive power and support AC grid stability, which is why they are used in flexible AC transmission systems (FACTS) and in connecting offshore wind farms. As renewable generation—solar and wind—grows, grid-connected inverters that convert DC from panels and turbines into grid-quality AC have become ubiquitous, and their control is now a major research area because inverter-dominated grids behave differently from grids built around spinning generators.
The Present
Today power electronics spans a huge range, from milliwatt converters inside phones to gigawatt HVDC links10. The field's main approaches descend directly from the history above: PWM-controlled switched-mode converters with averaged models and feedback compensation; phase-controlled thyristor converters for very high power; resonant and soft-switched topologies where high frequency or low noise is needed; and wide-bandgap devices where efficiency and power density justify the cost. Electric vehicles, renewable energy, data centers, and electrified heating and transport are driving demand for higher efficiency, higher power density, and better reliability. Open questions include how to make wide-bandgap devices cheap and reliable enough to displace silicon broadly, how to control millions of grid-connected inverters so they support rather than destabilize the grid, how to integrate power conversion with thermal and mechanical design in compact systems, and how to build converters that last decades with minimal maintenance. The switch, the magnetic component, and the control loop remain the field's core, and the history of power electronics is the history of making each of them better.
References
- Power electronics (Devices, History, Power MOSFET), Wikipedia
- Rectifier, Wikipedia
- Thyristor (History), Wikipedia
- Phase-fired controller, Wikipedia
- Insulated-gate bipolar transistor, Wikipedia
- Buck converter, Wikipedia
- Pulse width, Wikipedia
- Pulse-width modulation, Wikipedia
- Resonant converter, Wikipedia
- Power semiconductor device, Wikipedia
The frameworks of Power Electronics
Each framework is a way of working the field has used: when it held, and the question it answers.
- 1920-Present
Phase-fired controller
How can a switch's firing moment set the average output voltage?
- 1955-Present
Power Semiconductor Device Physics and Design
How can a semiconductor block high voltage and carry high current?
- 1960-Present
Electric Machine Drives and Motion Control
How can a motor's speed and torque be controlled precisely?
- 1970-Present
Pulse-Width Modulation
How does switching on and off at a fixed rate set the output?
- 1970-Present
Switched-mode power supply
How can a power supply convert voltage with little loss?
- 1971-Present
Field-Oriented Control
How can an induction motor be made to behave like a DC motor?
- 1975-Present
Averaged Small-Signal Modeling
How can a switching converter's behavior be predicted and stabilized?
- 1980-Present
Resonant and Soft Switching
How can switching losses and noise be reduced at high frequency?
- 1990-Present
Grid-Connected Converter Control
How can a converter feed power into the grid cleanly and stably?
- 2010-Present
Wide-Bandgap Power Devices
Can new semiconductor materials switch faster and handle more power?
How the ideas connect
Each arrow runs from an earlier idea to the later one it shaped. The list below says what passed between them.
Wide-Bandgap Power Devices grew out of Power Semiconductor Device Physics and Design
Wide-bandgap devices are a direct extension of power semiconductor device physics to materials with larger bandgaps and breakdown fields. SiC and GaN design work applies the same doping, breakdown and thermal-management concepts developed for silicon power devices.
Field-Oriented Control grew out of Electric Machine Drives and Motion Control
Field-oriented control grew out of electric machine drives as a way to control induction motors with the torque and flux decoupled. It was developed by drive engineers and required the fast switching and computation that drives were already pushing.
Switched-mode power supply grew out of Pulse-Width Modulation
Pulse-width modulation is the control method that made switched-mode supplies regulate their output predictably. The duty ratio set by PWM is the regulating variable in buck, boost, flyback and bridge converters, so the supply is built around the modulation scheme.
Power Semiconductor Device Physics and Design influenced by Phase-fired controller
Phase control established the method of varying firing angle to regulate output, which the thyristor inherited directly when GE announced it in 1957. Thyristor phase-controlled rectifiers kept the same firing-angle principle, so device design had to meet the blocking and latching requirements that phase control imposed.
Carried by General Electric thyristor (1957).
Pulse-Width Modulation influenced by Power Semiconductor Device Physics and Design
The power transistor that could be turned off at will, practical in the 1970s, made fixed-frequency switching with a controlled duty ratio feasible. PWM depends on a gate-controlled switch that can be turned on and off many times per cycle, which the thyristor could not do.
Switched-mode power supply influenced by Power Semiconductor Device Physics and Design
Switched-mode supplies became practical only when power BJTs and MOSFETs could be switched off on demand at high frequency. Device physics and design set the switching speed and losses that determined converter topology and frequency.
Field-Oriented Control influenced by Pulse-Width Modulation
Field-oriented control needs a voltage-source inverter switched by PWM to synthesize the commanded stator currents. The modulation method supplied the actuator that made independent flux and torque control practical.
Averaged Small-Signal Modeling influenced by Pulse-Width Modulation
Averaged small-signal modeling takes the fixed-frequency PWM waveform as its starting point and averages over one switching cycle. The duty ratio becomes the control input of the linearized model, so the modeling method is defined around PWM operation.
Resonant and Soft Switching influenced by Pulse-Width Modulation
Hard-switched PWM at rising frequency produced switching losses and EMI that limited performance. Resonant and soft-switching techniques were developed to shape the waveforms around the PWM switch transitions and reduce those losses.
Grid-Connected Converter Control influenced by Pulse-Width Modulation
Grid-connected converters use PWM to synthesize currents and voltages with controlled harmonic content. The modulation method carried over directly from motor drives and supplies into grid interface control.
Averaged Small-Signal Modeling influenced by Switched-mode power supply
As switching supplies spread, designers needed to predict and stabilize their loop behavior, which drove the development of averaged small-signal models. The converter topologies of switched-mode supplies were the systems the modeling method was built to analyze.
Grid-Connected Converter Control influenced by Averaged Small-Signal Modeling
Averaged small-signal models and transfer functions were applied to grid-connected converters to design current and voltage loops and assess stability against grid impedance. The modeling method carried over from converter design to grid interface control.
Electric Machine Drives and Motion Control influenced by Phase-fired controller
Phase-controlled rectifiers supplied the adjustable DC voltage that early DC motor drives used to control speed and torque. The firing-angle method carried over into drive controllers before choppers and inverters took over.
Resonant and Soft Switching influenced by Switched-mode power supply
The push for smaller, higher-frequency switched-mode supplies made hard-switching losses the limiting factor. Resonant converters were pursued as an alternative for applications such as server supplies and induction heating.
Grid-Connected Converter Control influenced by Field-Oriented Control
Field-oriented control's dq-axis current regulation was adapted to grid-connected converters, where active and reactive current are controlled in a synchronous reference frame. The control structure passed from motor drives to grid interfaces.
Wide-Bandgap Power Devices influenced by Resonant and Soft Switching
Wide-bandgap devices switch faster and at higher frequency, which makes soft-switching and resonant techniques more attractive to contain losses and EMI. The earlier methods were taken up again for the new devices.
Beyond the field
Where Power Electronics's ideas came from in other fields, and what they led to there: the strongest 12 of 35 links.
Power Semiconductor Device Physics and Design influenced by Electronic Devices and Semiconductor Physics in Electrical Engineering
Power semiconductor design grew directly out of the electronic devices and semiconductor physics tradition, taking its junction models, carrier-transport concepts and device-characterisation methods and extending them to high-voltage, high-current structures.
Power Semiconductor Device Physics and Design influenced by Solid-State Physics and Band Theory in Semiconductor Electronics
Band theory and solid-state physics supplied the conceptual basis for understanding doping, carrier concentration and breakdown that power device designers applied to thyristors and power transistors.
Power Semiconductor Device Physics and Design influenced by Doping and junction engineering in Semiconductor Materials
Doping and junction engineering techniques developed for signal transistors were taken up and extended in power devices, where deep diffusions, lifetime control and junction termination became central design concerns.
Power Semiconductor Device Physics and Design influenced by Semiconductor device physics in Condensed Matter
Semiconductor device physics, crystallised with the invention of the transistor in 1947, provided the junction and transport theory that power device design adapted to high-power structures.
Carried by William Shockley; John Bardeen; Walter Brattain.
Electric Machine Drives and Motion Control influenced by Electric machine in Electrical Engineering
Electric machine drives and motion control are built on the theory and construction of electric machines, taking their torque-production models and equivalent circuits as the plant to be controlled.
Field-Oriented Control influenced by Control Theory in Applied Mathematics
Field-oriented control was formulated using state-variable and feedback control theory, transforming the AC machine into an independently controlled flux and torque system through control-theoretic decoupling.
Carried by Felix Blaschke.
Averaged Small-Signal Modeling influenced by Small-signal model in Circuit Analysis
Averaged small-signal modeling applies the small-signal linearization of circuits around an operating point, developed for transistor amplifiers, to switching converters. Middlebrook and Cuk's state-space averaging linearizes the converter to obtain a small-signal model in the same sense.
Carried by R. D. Middlebrook; Slobodan Cuk.
Grid-Connected Converter Control led to Inverter-based and grid-forming resources in Power Systems
Grid-forming and inverter-based resource control grew directly out of grid-connected converter control, extending converter regulation from current-following to voltage-forming behaviour.
Wide-Bandgap Power Devices grew out of Power semiconductor device in Semiconductor Electronics
Wide-bandgap power devices are a branch of power semiconductor device development, extending the device family to SiC and GaN. They grew directly out of power device engineering as new materials were applied to the same device structures.
Wide-Bandgap Power Devices grew out of Power Electronics in Electrical Engineering
Wide-bandgap power devices are a branch of power electronics, supplying faster and higher-temperature switches for converters. The subfield grew out of power electronics as SiC and GaN devices entered converter design.
Wide-Bandgap Power Devices influenced by Epitaxy and band-gap engineering in Semiconductor Materials
Wide-bandgap power devices depend on epitaxy and band-gap engineering, since SiC and GaN device layers are grown by epitaxy and their heterostructures designed through band-gap engineering. The GaN HEMT in particular rests on AlGaN/GaN heteroepitaxy.
Phase-fired controller influenced Power Electronics in Electrical Engineering
Phase-fired control of thyristors, developed for rectifiers and AC controllers from the 1920s onward, became one of the basic modulation techniques taken up by power electronics. The firing-angle control concept passed directly into the later field's converter control methods.

Power Electronics is a planet in Nousfarer
Its city has a tower for each of these 10 frameworks. Land, walk in, and climb one concept at a time.
Land on Power ElectronicsRelated fields
Fields its ideas are linked to
- Electrical Engineering 7 links
- Semiconductor Electronics 6 links
- Power Systems 5 links
- Circuit Analysis 2 links
- Semiconductor Materials 2 links
- Condensed Matter 2 links
- Aerospace Propulsion 1 link
- Control Theory 1 link
- Process Control 1 link
- Transportation Engineering 1 link
- Action And Motor Cognition 1 link
- Embedded Systems 1 link
More in Electrical Engineering
- Circuit Analysis
- Communication Systems
- Control Systems
- Digital Systems
- Electrical Engineering
- Electromagnetics
- Information Theory
- Photonics
- Power Systems
- Rf And Microwave Engineering
- Semiconductor Electronics
- Signal Processing
- Signals And Systems
- Vlsi And Integrated Circuit Design
See where Power Electronics sits on the Map of Human Knowledge